YAKESTYLE 1PCS 5v/3.3v CH340G Serial Converter USB 2.0 To TTL 6PIN Module for PRO mini NEW

£9.9
FREE Shipping

YAKESTYLE 1PCS 5v/3.3v CH340G Serial Converter USB 2.0 To TTL 6PIN Module for PRO mini NEW

YAKESTYLE 1PCS 5v/3.3v CH340G Serial Converter USB 2.0 To TTL 6PIN Module for PRO mini NEW

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

The access points normally are running at 115kbit and will need reliable transfer for binary uploads.

In the IDE, go to File/Examples/Basics/Blink and load the sketch. If you have performed the previous steps correctly, the IDE should be able to communicate with the Arduino and upload the sketch. Eventually you will see LED 13 (on the board, blue) flashing once per second. Blue LED on board flashes once per second (with “blink” sketch) The analogue header doesn’t fit because of the reset button. Use sandpaper to make the analogue header thinner. Arduino clones need specific drivers, different from the standard ones that come with the Arduino IDE

6 Comments

I have also found that these drivers work fine when connecting the LoLin NodeMCU V3 to my Windows 7 PC (I had to do nothing, since I had already loaded the drivers for my cheap Chinese Arduino Nano clones). I suspect the same will be true for the Amica v0.9 (yellow or blue PCB) NodeMCUs (both considered out-dated) and the DoIt/SmartArduino brand NodeMCU V2. Both of these boards also use a WCH CH340G USB-to-UART bridge chip. This is a simple guide that will teach you how to take the first steps with the BTE13-010 module, a cheap Arduino mini clone. We will go through the 4 basic steps necessary to get it working immediately and without problems: Often the FTDI based ones are preferred. The FTDI chip is very expensive in comparison with other USB to TTL bridges, but they are often preferred. So look for FTDI when searching USB to TTL. Often FTDI ones use fake clones instead of the genuine and expensive FTDI, so if it's too cheap then it's probably not genuine FTDI. Soldering headers can be pretty easy if you take advantage of a breadboard. Place them on it and then put Arduino over connectors. Before starting, we specify that this tutorial can be used to learn how to install the drivers of the CH340G module (Serial – USB converter), on which the communication between the Arduino mini and the PC is based.

I wanted to hide the USB serial and USB sound dongles in the box so I looked through my junk box for a USB Hub. I found a 4 port hub so I decided to add a USB memory key.Our sketch is based on the one found by default on the IDE and which is called “Sweep”, with the addition of a 16×2 LCD display that shows the value of the rotation angle of the servo. Basically, it rotates the servo and shows how much it rotated on the display. I have that model, too. That board is a mistake by design. It was very infuriating to find out the power supply was changing, while the levels on the data pins voltage were always 0..5V. soldering material and equipment (in this regard you can watch our tutorial Yet another tutorial on how to solder) Turns out that the driver isn’t signed and in Yosemite, driver files must be signed to be used. There’s a command we can issue to bypass this.

Another alternative is to buy the FTDI chip from a reliable vendor, so to be sure it is genuine, then wire your own. Here's an example of a FT232RL wired by hand to a 0.1 inch perfboard. I recently posted an instructable for an FLDigi compatible interface. It was largely based on a Hamcomm interface I designed as a hand out for a Ham / PC Usergroup talk I gave in 2005. The main difference between HamComm and FLDigi is that FLDigi can use a tone on the right channel to key the rig eliminating the need for a serial port to drive a relay that Hamcomm used. the connector to be soldered on the part of the analog inputs is too wide, thin it slightly by rubbing it on sandpaperWARNING: by installing a new version of the Arduino IDE you risk overwriting the CH340G drivers. For this reason we suggest you not to install the IDE using the executable (.exe) but to use a “portable” version. If you accidentally overwrite the CH340G drivers, uninstall the IDE with the drivers and reinstall everything from scratch. Global variables use 9 bytes (0%) of dynamic memory, leaving 1,015 bytes for local variables. Maximum is 1,024 bytes.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop